What size thread is a 10 AN
Russell Performance Technical Support
AN Size | Metal Tube O.D. | Thread Size |
---|---|---|
-6 AN | 3/8" | 9/16" – 18 SAE |
-8 AN | 1/2" | 3/4" – 16 SAE |
-10 AN | 5/8" | 7/8" – 14 SAE |
-12 AN | 3/4" | 1-1/16" – 12 SAE |
What size hose is 10 an
In another example, a -10 tube would indicate a tube with an outside diameter of 10/16", or 5/8".
What is 6 an fitting
In bolts the number refers to the diameter of the bolt whereas in a fitting it refers to the OD of the tube and thereby have different threads. For example, AN6 bolt has a 3⁄8-24 thread whereas an -6 AN fitting has a 9⁄16-18 thread.
What are the sizes of an fittings
AN fittings range in size from -2 (dash two) to -32 in irregular steps that each equates to the outer diameter of the tubing. The outer diameter of the tube or hose that each fitting is to be used for is correlated with the inner diameter of the fitting itself.
What size is 6AN in MM
Hex sizes are not standardized.
Female Thread Minor ID | AN Size | Could Also Be! |
---|---|---|
0.330" to 0.340" | 3AN | M10* (0.330" – 0.341") |
0.383" to 0.395" | 4AN | 1/8 NPT (0.36"), M12* (0.398") |
0.502" to 0.515" | 6AN | 1/4 NPT (0.47"), M14 (0.499") |
0.682" to 0.696" | 8AN | M20* (0.681" – 0.699") |
What does an stand for in fuel lines
AN tubing was designed to create a standard that could provide a flexible alternative to hard line tubing for aircraft and military vehicles. AN stands for Army Navy and is measured in AN Sizing.
How do I tighten my fittings
Tightening Method 2: Counting Flats
- Step 1: Assemble the fittings. Screw down the female nut until finger-tight.
- Step 2: Mark the fittings.
- Step 3: Tighten the fittings.
- Step 4: Mark the fittings again.
What size is SAE 10
SAE 45° Flare (SAE J512)
Inch size | Dash size | Male Thread O.D. (in) |
---|---|---|
5⁄8 | -10 | 7⁄8 |
3⁄4 | -12 | 11⁄16 |
7⁄8 | -14 | 1 1⁄4 |
1 | -16 | 1 3⁄8 |
What are sewing thread sizes
The larger the number, the finer the thread (a 50/2 will be thinner than a 30/2). The second number indicates the number of strands, or plies, twisted together. It is obvious that a 50/3 is heavier than a 50/2 because it has three strands of a size 50 thread twisted together and the 50/2 has only two.
What is the standard thread for M10
Basic Metric Thread Chart (M1 – M100)
Diameter | Coarse Pitch | Fine Thread Pitches |
---|---|---|
M10 | 1.5 | 1.25 |
M11 | 1.5 | 1 |
M12 | 1.75 | 1.5 |
M14 | 2 | 1.5 |
What size is a 10 AN fitting
AN Fittings and Hose Sizes Chart
AN Size | Hose / Tube O.D. | SAE Thread Size |
---|---|---|
-8 | 1/2 in. | 3/4 in.-16 |
-10 | 5/8 in. | 7/8 in.-14 |
-12 | 3/4 in. | 1 1/16 in.-12 |
-16 | 1 in. | 1 5/16 in.-12 |
What size hose is an
The Good News
Male Thread Size | AN Size* | Hose ID** |
---|---|---|
7/16-20 | 4AN | 0.22" |
9/16-18 | 6AN | 0.34" |
3/4-16 | 8AN | 0.44" |
7/8-14 | 10AN | 0.56" |
What is an an line
The AN thread (also A-N) is a particular type of fitting used to connect flexible hoses and rigid metal tubing that carry fluid. It is a US military-derived specification that dates back to World War II and stems from a joint standard agreed upon by the Army and Navy, hence AN.
What size is 12 AN hose
For example: a 3/8" standard hose equals -6 AN.
Russell Performance Technical Support.
AN Size | Metal Tube O.D. | Thread Size |
---|---|---|
-6 AN | 3/8" | 9/16" – 18 SAE |
-8 AN | 1/2" | 3/4" – 16 SAE |
-10 AN | 5/8" | 7/8" – 14 SAE |
-12 AN | 3/4" | 1-1/16" – 12 SAE |
What is the ID of a 58 garden hose
Hose Diameter
Majority of the outside diameter of 5/8 inch hoses measure between 0.77” and 1”. If the outside diameter of your hose is less than 0.77”, it is most likely a 1/2 inch hose.
What is the thread pitch of a an fitting
Each AN size also uses its own standard thread size. AN fittings are a flare fitting, using 37° flared tubing to form a metal-to-metal seal. They are similar to other 37° flared fittings, such as JIC, which is their industrial variant.
How big is a 6AN fitting
AN Fitting Size Guide
Male Thread Size | AN Size* | Hose ID** |
---|---|---|
7/16-20 | 4AN | 0.22" |
9/16-18 | 6AN | 0.34" |
3/4-16 | 8AN | 0.44" |
7/8-14 | 10AN | 0.56" |
What size hose is 6AN
AN Fitting and Hose Sizes
Male Thread Size | AN Size* | Hose ID** |
---|---|---|
3/8-24 | 3AN | 0.13″ ** |
7/16-20 | 4AN | 0.22″ |
9/16-18 | 6AN | 0.34″ |
3/4-16 | 8AN | 0.44″ |